Home

ballooncar1

Balloon Rocket Car – learn the concepts of Newton’s Law of Motion, friction, jet propulsion, and air resistance by designing and constructing a balloon powered rocket car. Build a Balloon Rocket Car that can extract the most energy out of the inflated balloon and make the vehicle travel the longest distance.

There is a kit with materials for 2 cars for each Period.

  • Use Engineering Design Process to record your work. It is important to keep track of Improvements – What needed improving? Why? What changes did you make? What were the results?
  • Record the distance traveled by each “run” of your cars. Which of your cars performed best? Why?

On Wednesday November 16, compare the distances recorded for all cars in all periods. Which car performed best? Why? What would you do differently if you do this project again?

Balloon Rocket Car
http://www.hometrainingtools.com/a/balloon-rocket-car-project/

The principles of rocketry apply to more than flying rockets – with this project you can make a ‘rocket car’ that is powered by pressurized gas (air in a balloon!)

What You Need:

16-20 oz. plastic water bottle
Drinking straws
Wooden shish-kabob skewers
4 plastic bottle caps
Balloon
Duct tape or masking tape
Nail, hammer, knife, scissors

What You Do:

The water bottle forms the chassis, or body, of your balloon car. You can start by mounting the wheels on this body.

  1. Cut a drinking straw into two pieces as long as the water bottle is wide. Use strips of tape to attach them to the bottle – one near the front and one near the back. The axles for the wheels will run through these straws, so line them up carefully so the wheels won’t be crooked.
  2. Use a hammer and a small nail to poke holes through the center of four bottle caps. Cut two pieces of a wooden skewer about an inch-and-a-half longer than the pieces of straw you taped to the bottle. Push one end of each skewer through the hole in the center of a bottle cap. If the cap doesn’t fit snugly on the skewer, use some modeling clay to hold it in place. Next, thread the skewers through the straws on the bottle and attach the other wheels to the other ends. Make sure your car rolls smoothly.
  3. Stretch out a large balloon by blowing it up and then letting the air out of it a few times. Next, make a nozzle. The size of the nozzle is very important. If it is too small, the air can’t escape with enough force to propel the car forward. If it is too big, the air will escape too fast and the car won’t go very far. Create the nozzle by taping four drinking straws together. Insert the straws into the mouth of the balloon and seal the opening by wrapping a strip of duct tape around it several times.
  4. To mount the balloon/nozzle on the car, use a knife to cut two perpendicular slits (to make an X) in the top of the car about 4′ back from the mouth of the bottle. Thread the nozzle through this opening and out through the mouth of the bottle. Leave about an inch of the nozzle sticking out of the mouth.
  5. Find a hard surface, like a long table, linoleum floor, or sidewalk. Blow up the balloon through the straws at the mouth of the bottle. Pinch the base of the balloon to prevent the air from escaping too soon. Set the car down, let go of the balloon, and watch it go!

The air in the balloon is gas under pressure. The air pushes against the balloon, causing it to expand, but the balloon is also pushing back on the air. The pressure of the balloon pushes the air right out through the nozzle, which creates thrust that propels the car forward.

Keep track of how long the car rolls and how far it goes. Try it several times, then try changing the design to see if you can get it to go farther or faster. How will it work if you only use three straws for the nozzle? What if you use a bigger or smaller balloon? Does the car go farther on linoleum or the sidewalk? Why do you think this might be? Will the car go farther if you start it at the top of a ramp?

http://www.hometrainingtools.com/a/balloon-rocket-car-project/

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s